产品展示

Product Center

Product Center > ZH series pneumatic actuator

current position: Home > Product Center > ZH series pneumatic actuator
ZH Series Pneumatic Actuator Market

ZH Series Pneumatic Actuator Market

  • Category:ZH series pneumatic actuator
  • Browse number:
  • QR code:
  • Release time:2022-08-16 13:44:07
  • Product description

ZH Series Pneumatic Actuator Market

Technical standards for pneumatic actuators

Products in each industry have their own standards, and products that meet various requirements can be applied to various industries. Among them, the products in the valve industry strictly comply with their standards. Only when they meet all aspects of the standards, can they ensure that there will be no failures in operation. Today we will focus on the pneumatic actuator products in the industry. The function of the pneumatic actuator is to adjust the valve actuator through air pressure opening and closing. In the actual operation process, it is necessary to fully understand the technical standards of each link. Here's a brief introduction

1、 Standards to be met structurally

1. The pneumatic device is mainly made of air cylinder. The piston, gear shaft, end cover, seal and screw sleeve pneumatic device shall also include opening indication, travel limit, solenoid valve, positioner, pneumatic element and manual mechanism. It is composed of signal feedback and other components.

2. The connection size of pneumatic device and valve shall meet the requirements of ISO5211 (bottom), GB/T12222 and GB/T12223.

3. When the air supply is interrupted, the pneumatic device with manual mechanism shall be able to use its manual mechanism to open and close the valve. When facing the handwheel, the handwheel or handle shall be rotated counterclockwise until the valve is opened, and clockwise until the valve is closed.

4. When the end of the piston rod is an internal and external thread, there should be a wrench opening suitable for the standard wrench.

5. The sealing ring of the piston shall be easy to replace and repair.

6. For pneumatic device with buffer mechanism, the stroke length of buffer mechanism can refer to Table 1.

7. The pneumatic device with adjustable buffer mechanism shall have a mechanism to adjust the buffer effect outside the cylinder.

8. The thread size of cylinder inlet and outlet shall meet the requirements of MANURNORM (accessory standard) GB/T7306.1. GB/T7306.2 and GB/T7307.

Pneumatic straight stroke actuator

2、 Standards to be met in performance

1. The rated output force or torque of the pneumatic device shall meet the requirements of GB/T12222 and GB/T12223

2. In case of no load, input the air pressure in the cylinder as specified in Table 2, and the action is stable without blockage and creeping.

3. The pneumatic device starts under the air pressure of 0.6MPa The output torque or thrust in both directions shall be closed, and its value shall not be less than the value marked on the sign of the pneumatic device. The action shall be flexible without deformation and other abnormal phenomena.

4. When the sealing test is conducted under the working pressure, the amount of air leaking from each back pressure side shall not exceed (3)+0.15D) cm3/min (standard state). The amount of air leaking from the output shaft shall not exceed (3)+0.15d) cm3/min.

5. The strength test shall be conducted with 1.5 times of the large working pressure. After maintaining the test pressure for 3min, the cylinder end cover and static sealing parts shall be free of leakage and structural deformation.

6. Action life time, pneumatic device simulates valve action. When maintaining the output torque or thrust capacity in both directions, the number of opening and closing operations shall not be less than 50000 times (the opening and closing cycle is once).

7. When the piston moves to the end of the stroke, the pneumatic device with buffer mechanism is not allowed to impact.

3、 Appearance standard

1. Cast cylinder end cover, end flange and box shall be free of scratches, cuts, air holes and burrs.

2. The coating or chemical treatment layer on the external surface of the pneumatic device shall be flat, smooth, uniform in color, and free of oil stain, indentation and other mechanical damage.

气动执行器

Tags

Recently Viewed:

Related products

news.related_news

Copyright © Wenzhou Mocheng Automatic Control Valve Co., Ltd All rights reserved record number:浙ICP备19000689号-1 Mainly engaged inPneumatic actuator,Pneumatic valve actuator,Manufacturer of pneumatic valve, Welcome to inquire!
Technical Support: Wenzhou Successkj Co., Ltd

As the new Advertising Law stipulates that absolute words are not allowed to appear on all pages, we support and follow the Advertising Law. In order not to affect consumers' normal browsing, the company has been urgent to check and modify the obvious areas of the shop page, and hereby solemnly states that all absolute words of the shop are invalid and not used as compensation reasons; The company will never accept and compromise the online fraud in the name of fighting against counterfeits in any form. Please make way for real consumers. The protection of rights is two-way. I hope all consumers will understand, and those who are trying to seek illegitimate interests will appreciate it!